Enterprise AI Platform For
Automotive Software Teams
Embedder Automotive helps your team implement, migrate, and test ECU software across MCU generations and vehicle programs.
A dark car in a bright engineering hall, its front redrawn as signal lines. Embedder writes, builds, and verifies the firmware that runs on a vehicle's hardware.
Works with the silicon you already use
Embedder supports 600+ platforms from 14 chip and board manufacturers, and the probes and instruments already on your bench.
Supported MCU Ecosystems
View Full List(opens in a new tab)Help across the entire development lifecycle
Drivers, AUTOSAR configuration, compliance, debugging, and testing, in the tools your teams already use.
Development
From first bring-up to a tested, traced change.
Drivers & bring-up
Drivers from datasheets and SVDs, complex device drivers included.
Drivers & bring-up
Drivers from datasheets and SVDs, complex device drivers included.
AUTOSAR & MCAL
BSW, COM, and RTE configured from a spec or DBC, in your configurator.
AUTOSAR & MCAL
BSW, COM, and RTE configured from a spec or DBC, in your configurator.
MISRA compliance
Every change checked by static analysis, with the report attached.
MISRA compliance
Every change checked by static analysis, with the report attached.
Debug & root cause
Agents drive your debug probe to find faults.
Debug & root cause
Agents drive your debug probe to find faults.
HIL & SIL testing
Tests generated and run on benches, simulators, and virtual prototypes.
HIL & SIL testing
Tests generated and run on benches, simulators, and virtual prototypes.
Traceability
Every change linked to its requirement, in the tool you already use.
Traceability
Every change linked to its requirement, in the tool you already use.
Every change comes with evidence
Embedder works inside the V-cycle your teams already follow. Engineers approve the plan, review the evidence, and decide what merges.
Who Does What
Embedder is a development tool. It does not replace your ISO 26262 and ASPICE process.
Code and software tests
Embedder writes the design and code, and runs the tests engineers approved.
Code and software tests
Embedder writes the design and code, and runs the tests engineers approved.
Requirements and architecture
Embedder drafts them. Engineers set ASIL and faults, and accept the result.
Requirements and architecture
Embedder drafts them. Engineers set ASIL and faults, and accept the result.
Safety concept, system, and validation
These stay with your engineers.
Safety concept, system, and validation
These stay with your engineers.
Qualified Tools
Like an engineer, Embedder works with your qualified tools.
Functional equivalence
The code can vary between runs. The verified behavior does not.
Every run must pass the same tests and baseline comparison before it merges. Model versions are pinned, and upgrades are opt-in and run against a regression suite first.
Functional equivalence
The code can vary between runs. The verified behavior does not.
Every run must pass the same tests and baseline comparison before it merges. Model versions are pinned, and upgrades are opt-in and run against a regression suite first.
From prototype to SOP
Autonomy narrows as a program nears start of production.
High in concept and A-samples, guided in B-samples, and low from C-samples to SOP, where code is baselined and changes follow your qualified toolchain and change requests.
From prototype to SOP
Autonomy narrows as a program nears start of production.
High in concept and A-samples, guided in B-samples, and low from C-samples to SOP, where code is baselined and changes follow your qualified toolchain and change requests.
Evidence Per Change
The model proposes. Deterministic tools decide.
With every pull request
Build and test results, a MISRA report, a requirement link, and the run record.
- Build results from your own compiler
- Test results, run on hardware or a virtual prototype
- MISRA report from your static analyzer
- Requirement link, back to the requirement the change implements
- Run record: the model, inputs, and tool calls behind the change
With every pull request
Build and test results, a MISRA report, a requirement link, and the run record.
- Build results from your own compiler
- Test results, run on hardware or a virtual prototype
- MISRA report from your static analyzer
- Requirement link, back to the requirement the change implements
- Run record: the model, inputs, and tool calls behind the change
Your existing code, verified on the new MCU
Embedder maps what differs between the two devices. Parallel agents then port the code module by module, each looping until your tests pass.
Migration Paths
The same steps, whichever way the code is moving.
Across MCU generations
Tested from single peripherals up to communication stacks.
Across MCU generations
Tested from single peripherals up to communication stacks.
Between MCU families
Within one vendor's portfolio, in either direction.
Between MCU families
Within one vendor's portfolio, in either direction.
Between silicon vendors
Existing code moved from one vendor's MCUs onto another's.
Between silicon vendors
Existing code moved from one vendor's MCUs onto another's.
How It Works
From your existing project to a reviewed pull request.
SWE.1 · Requirements
Starting point
Your project, your tests, and a recorded baseline.
- Your existing project: code, MCAL, and ARXML
- Requirements and your test suite
- A behavior baseline recorded on your ECU
- Target device docs: errata, SVDs, and the vendor's driver libraries
SWE.1 · Requirements
Starting point
Your project, your tests, and a recorded baseline.
- Your existing project: code, MCAL, and ARXML
- Requirements and your test suite
- A behavior baseline recorded on your ECU
- Target device docs: errata, SVDs, and the vendor's driver libraries
Impact Analysis
Differences mapped
Mapped area by area. An engineer approves the plan.
- ADC
- CPU core
- Timers
- CAN
- Security module
- Board: pins, clocks, memory map
Impact Analysis
Differences mapped
Mapped area by area. An engineer approves the plan.
- ADC
- CPU core
- Timers
- CAN
- Security module
- Board: pins, clocks, memory map
SWE.3 to SWE.5
Embedder parallel agents
Code, unit and integration test, on your ECUs and benches.
- Startup, toolchain, clocks, and ports
- ADC, timers, CAN, and crypto, one agent each
- Write, build, flash, test, fix: each agent loops until your tests pass
- Comm stacks and MCAL integration
SWE.3 to SWE.5
Embedder parallel agents
Code, unit and integration test, on your ECUs and benches.
- Startup, toolchain, clocks, and ports
- ADC, timers, CAN, and crypto, one agent each
- Write, build, flash, test, fix: each agent loops until your tests pass
- Comm stacks and MCAL integration
SWE.6 · Verification
Output
Verified against your baseline. An engineer reviews and merges.
Evidence comes per module:
- Pull request
- Build log
- Hardware test results
- MISRA report
- Requirement link
SWE.6 · Verification
Output
Verified against your baseline. An engineer reviews and merges.
Evidence comes per module:
- Pull request
- Build log
- Hardware test results
- MISRA report
- Requirement link
SWE.1 to SWE.6
Your requirements tool
Requirements come in from it, and traceability is kept current.
SWE.1 to SWE.6
Your requirements tool
Requirements come in from it, and traceability is kept current.
Meet Embedder, your team's
autonomous firmware engineer

